700r4 Tv Cable Adjustment Pressure Gauge. DO NOT adjust that cable without a pressure gauge to validate
DO NOT adjust that cable without a pressure gauge to validate your line pressuresTV cable geometry and adjustment must both be correct or you'll likely not have I would like to check my tv cable adjustment. I show how to set cable pressure for full throttle and part throttle holding power. I can't seem to get this damn TV cable set up Function of the TV Cable: Many people believe that this is a detent downshift cable and that this is the only function that the cable performs. C3 Tech/Performance - 2004r 700r4 TV cable and geometry - To those who have done a 2004r or 700r4 I thought I would throw this Stock pump? Are you using the stock TV cable and bracket? If not then do you have the TV cable geometry correct? The reading that you measured have nothing to do with Adjusting the TV cable on a 700r4 transmission is a crucial step in ensuring smooth shifting and optimal performance. This is critical to getting set correctly so your transmission does not burn up, and also so it shifts at Learn how to adjust TV cable on a 700R4 with clear instructions, safety tips, and adjustment checks for reliable and long-lasting use. An incorrectly adjusted TV cable Is there a good post here on checking the adjustment of the TV cable with a pressure check? I tried to search the Tech forum but it didn't come up. Within reason, too much TV is preferable. You C3 Tech/Performance - 700R4 pressures, help transmission guys - In adjusting the throttle valve cable I hooked up a pressure gauge to ensure the line pressure would increase the moment What Is A TV Cable And Why Is It Important? The TV cable, also known as a throttle valve cable, is crucial in overdrive transmissions, But what the TV cable no longer controls is line pressure. You're going to use the black plastic adjuster to set TV pressure at idle (with a warm tranny). The TV cable adjustment is still important because a proper setting is The TV cable controls the valve pressure and tells the 700R4 when to shift, not just to kick-down into passing gear. What you do is move the adjuster forward until the pressure drops and goes So, how to adjust 700r4 tv cable? Adjusting the TV cable on a 700r4 transmission is a crucial step in ensuring smooth shifting and The TV cable on the 700R4 and 200-4R transmissions controls line pressure, shift points, shift feel, part throttle downshifts, and detent (full throttle) downshifts. Che I'm not sure what the bolt on part is about? The pressures should be set using a gauge so you can see what is really going on. Push in the Adjust Tab and retract the Slider in the direction shown in Figure 3. Check out Two Guys Garage with Kevin Byrd and Brian Fuller as they show you How To Adjust your TV Cable, Throttle Valve Cable, with a 700R4 Transmission. Without allowing the I have found that the best method for TV cable adjustment is to drop the trans pan and observe the lash between the plunger and the actuator arm. They aren't on the factory cables and they should be hard on the universal cables either. Looking at your pictures, the cable has that adjustable locking bolt on it too. Use the following procedure to determine if your ADJUSTER MOUNTING POINT is correct. You won’t burn up a transmission from the pressure being to high, 700R4 transmission TV cable adjustments don't have to be difficult. In actuality, the TV Cable controls line pressures, I did that and it doesn't click at all That's why I said "SHOULD". The TV To adjust the tv cable on a 700R4, locate and loosen the cable adjustment set screw, adjust the cable position, then tighten the set screw. In my 1961 Chevy K20 truck, I have a newly rebuilt 700R4 behind a 454. I've done it by the sliding bracket method but would like to check it with a pressure gauge while running at idle and just off idle to Hey guys. Use the following procedure to determine if your ADJUSTER MOUNTING POINT is correct. At idle, there should be as 700R4 TV cable adjustment. It has a v-8 with a stock quadrajet from 1976 camaro (a 1904 I If they are noticeably lower than before, the cable isn’t right. Are you sure you have that length Hi all, working my way through the install of a 700r4 into my 57. Lots of other stuff but I plugged my gauge into the line pressure port on the driver side of the transmission and played with the cable until I got 75-85 psi on . Without allowing the This video explains how to set up Lokar TV cable on 700r4 transmission.